free shipping at parts express

Tang Band 13-1761S 1/2" Silk Dome Tweeter Pair

Brand:|Model: 13-1761S|Part # 264-841
Tang Band's 13-1761S features a highly damped fabric diaphragm, neodymium magnet, and ferrofluid cooling. Sold in pairs.
In Stock
List Price$19.16
You Save23%
Your Price
Buy 4+$14.00
Part # 264-841

Product Details

Tang Band 13-1761S 1/2" Silk Dome Tweeter Pair

Tang Band's 13-1761S features a highly damped fabric diaphragm, neodymium magnet, and ferrofluid cooling. The tweeter's housing is small enough to fit within a 20 mm voice coil -- great for coaxial projects or anywhere a "micro" HF driver is required. Extremely smooth frequency response. Sold in pairs.

Product Specifications
  • Tweeter TypeSoft Dome
  • Cone / Dome Diameter1/2"
  • Impedance8 ohms
  • Power Handling (RMS)3.5 Watts
  • Frequency Response4,000 to 20,000 Hz
  • Sensitivity88 dB 1W/1m
Thiele-Small Parameters
  • Resonant Frequency (Fs)4,000 Hz
  • DC Resistance (Re)7.00 ohms
Mounting Information
  • Overall Outside Diameter0.77"
  • Cutout Diameter0.77"
  • Depth0.71"
Tang Band 13-1761S 1/2" Silk Dome Tweeter Pair
  • BrandTang Band
  • Model13-1761S
  • Part Number264-841
  • UPC844632069468
  • Product CategoryTweeters
  • Unit of MeasurePR
  • Product Rating
    (9 Reviews)
  • Weight0.05 lbs.
  • California Prop 65

    Warning: California residents only. Please note per Proposition 65 that this product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

View similar products to the Tang Band 13-1761S 1/2" Silk Dome Tweeter Pair
in the Tweeters product category.


Tang Band 13-1761S 1/2" Silk Dome Tweeter Pair
Tang Band 13-1761S 1/2" Silk Dome Tweeter Pair is rated 4.0 out of 5 by 9.
Rated 5 out of 5 by from Crystal Clear Highs!I wanted to build the wife some speakers for the bedroom tv. At the time she was using some PC speakers that weren't quite getting the job done. I paired these with the Goldwood 4" woofers (shielded) and some generic 2 way passives from ebay. I wish I could tell you what the crossover point is, but I can't. But what I can tell you is that if you're on the fence with these, just buy them. They are brilliant little tweeters.I will say however, the soldering pads make installation a bit tedious. I was using a cheap Harbor Freight soldering iron (I don't recommend this) so I had to hold the tip on the tweeter a lot longer than I was comfortable with. Then comes the issue of mounting. I just used a hole saw that was the exact diameter of the tweeter, burrowed a hole in the front baffle, and just hot-glued it from the back side.I think I'm going to put some of these in my car! I strongly recommend these for anyone that wants crystal clear highs in small spaces.
Date published: 2016-02-06
Rated 5 out of 5 by from Amazing!These little guys reproduces really amazing high range. I use this model with Wharfedale Modus 4" speaker, which produces good middle to high range. These addtional tweeter made the system far better. Now, I have to create enclosures.
Date published: 2014-06-13
Rated 5 out of 5 by from pleasantly surprisedWhen received my order, the pair came in a box about1.5" x 1" . Right away i expected them to be some type ofbuzzers.First order crossover at 5uF they fill the room with a great volume of sound. You know how they say dynamite comes in small packages ? These little guys are reminiscent of the saying. Paired with some Focal 6.5"woofers on the front channels of a surround receiver, they will take all of the 50-100 watts my receiver will throw at them. After years of blowing paper cone tweeters, these are the best tweeters .
Date published: 2012-06-02
Rated 4 out of 5 by from A little Tongue and CheekThese little guys distort and have no bass. I tried to use them for a subwoofer and... Just kidding!These are perfect for line arrays, but to sound good need to crossed fairly high (no I won't give away my "secret" x-over frequency). They are half inch so I recommend using these in a three way design or with a mid-woofer that is capable of being crossover at 5K!Great for what they are :)PS. My tongue and cheek is for the people rate a good product poorly because they fail to understand the spec sheet. If you don t understand the TS parameters: Qms, Qes, or Fs ask someone who knows. In the end it makes or breaks a design :)
Date published: 2009-12-10
Rated 4 out of 5 by from Great for line arrayI didn't find anything wrong with these so I'm not sure why an earlier review here had so many problems. Possibly a bad pair? Using them from 4000 Hz up non linear and linear distortion measurement results were very reasonable for such a small driver. I've just ordered 66 pair of these to be used in a CBT array for my home theatre center speaker. Because of the small size the center to center spacing will allow polar control to about 13 KHz. It will be interesting to see if I run into consistency issues, if so I'll post a follow up but right now based on what I've seen in the two samples I have very high hopes for
Date published: 2009-09-09
Rated 1 out of 5 by from sound awfulThese speakers sound absolutely awful, they ring, there distorted. I tried and tried to get a good sound out of them but don't think it is possible. Do yourself a favor and do not purchase these, you will just have to buy different ones if you care at all about the fidelity of your sound.
Date published: 2009-02-15
  • 2016-02-10T06:45CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.6
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_9
  • loc_en_US, sid_264-841, PRD, sort_mostRecent
  • clientName_PartsExpressInternational

Product Q&A

Get your questions answered from other customers
who own this product or have experience with it.
If your question requires design or troubleshooting information,
please email  for a prompt reply.
Tang Band 13-1761S 1/2" Silk Dome Tweeter Pair

suitable midbass for making these co-axial. Your recomendation please

Asked by: tkannan
These were originally designed for use in the Tang Band W3-1723SA which is no longer available. In order for this to work as a coaxial tweeter with any other driver a custom mount will have to be made. There are too many options to recommend, but it will work with basically any 3-4" full range driver we offer crossed around 8 kHz.
Answered by: MattP
Date published: 2015-09-03

Where and I find the Qms, Qes and Le for these tweeters... I'm trying to graph their EQ curve using X-Over Pro and I cant calculate the Impedance EQ with out them... Any help would be great?

Asked by: Jayger
The values are below.Qms: 1.541Qes: 5.178Qts: 1.187Le (measured at 1kHz): 0.417 mH
Answered by: MattP
Date published: 2014-11-18

I'm impressed with these, but need a recommendation. I have them paired with Fountek FR58EX full ranges, 1st order crossed at 5K..  They are "hot" compared to the 2.3dB woofer, so I want to attenuate them... What sort of resistor should I use inline?

Asked by: Mxseven
I would recommend two resistors in order to not change the crossover point of the speaker. A 3.3 ohm in series and a 3.7 ohm in parallel will drop the tweeter level about 8 dB which should help it blend better with the woofer.
Answered by: MattP
Date published: 2014-05-28

Is the tweeter sealed? Will I have an issue with leaving the back of the tweeter open to the woofer's shared cabinet

Asked by: Jorje
Yes these are sealed and do not need to be isolated from the woofer in any way.
Answered by: MattP
Date published: 2014-12-18

How to solder the leads?

These have no leads attached but appear to have two soldering pads. Which pad is positive? There is a red dot slightly closer to one of the pads but it isn't really clear.The specifications sheet did not add any detail or diagrams on the connection polarity. Thanks.
Asked by: Longfatty
Yes, use the red dot for (+) on both. This will insue like polarity. My understanding is that polarity is not critical with these tiny tweets.I would use low temp quality solder, a solder pencil with a fine tip and lightly tin your wire.
Answered by: Nitnub
Date published: 2014-04-09


I was wondering what have been your mounting solutions. It looks as if they have channels on them to hold them into place. I am assuming that its drill hole and epoxy, but I would like a removable solution.
Asked by: Doyne5
There is a screw hole in the middle in the back, but I haven't measured the screw size. You can take the tweeter to your local hardware store and find the proper size bolt to screw into it. I imagine it's somewhere around M4x.5, but I'm not sure.
Answered by: Circuitsoft
Date published: 2012-08-18
  • 2016-02-10T07:23CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.6
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_7
  • loc_en_US, sid_264-841, PRD, sort_recentQuestionsFirst
  • clientName_PartsExpressInternational

Recently Viewed Products

Parts Express FacebookParts Express TwitterParts Express YouTubeParts Express PinterestParts Express SpotifyParts Express Instagram
Live Chat Software