Pyle PLST6 1/2" Neodymium Tweeter Pair

Pyle PLST6 1/2" Neodymium Tweeter Pair

Brand:| Model: PLST6
Overview
This versatile mylar dome tweeter pair features a powerful neodymium magnet system and can be flush, swivel or surface mounted.
Highlights
  • Includes 12dB/oct crossovers
Part # 
267-748
Weight: 0.75 lbs.  
IN STOCK
List Price$28.99
You Save72%
Your Price
$7.97
Buy 12-up$7.50
Part # 267-748
Qty:  EA
Available Payment Methods

Product Details

Pyle PLST6 1/2" Neodymium Tweeter Pair

This versatile mylar dome tweeter pair features a powerful neodymium magnet system and can be flush, swivel or surface mounted. Ferro fluid enhancement to the voice coils extends the power handling capacity.

Specifications: • Frequency response: 1,300-22,000 Hz • Power handling: 75 watts RMS/150 watts max • Impedance: 4 ohms • SPL: 92 dB 1W/1m. 2-1/8" overall diameter • Requires 1-3/4" hole for flush mount • Includes 12dB/oct crossovers, mount kits, and hardware • Net weight: 1/2 lb. per pair.



Product Specifications
  • Tweeter TypePoly / Mylar Dome
  • Impedance4 ohms
  • Power Handling (RMS)75 Watts
Pyle PLST6 1/2" Neodymium Tweeter Pair
  • BrandPyle Audio
  • ModelPLST6
  • Part Number267-748
  • UPC068888708555
  • Product CategoryCar Audio Tweeters
  • Unit of MeasureEA
  • Product Rating
    (20 Reviews)
  • Weight0.75 lbs.
  • California Prop 65

    Warning: California residents only. Please note per Proposition 65 that this product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Similar Products

View similar products to the Pyle PLST6 1/2" Neodymium Tweeter Pair
in the Car Audio Tweeters product category.

Reviews

Pyle PLST6 1/2" Neodymium Tweeter Pair
Pyle PLST6 1/2" Neodymium Tweeter Pair is rated 4.0 out of 5 by 20.
Rated 5 out of 5 by from great productthey are the loudest little things ever i have 8 of them in my toyota 4runner and let me tell you something these little things are only hooked up to my deck but the can really pierce some ear drums the deck only puts out 80 watts per channel and i have 2 per channel amazingly little things
Date published: 2013-02-06
Rated 4 out of 5 by from Sounds Good, needs documentationSOUNDThese sound very nice. I installed them in a 2005 PT Cruiser in place of the factory dash mounted tweeters.Despite claims that they go down to 1.3kHz my calculations based on the component values in the high pass filter show a crossover point of 5.9kHz, significantly lower then the 12kHz crossover of the 24db/oct filter of Chrysler's stock tweeter. The increased upper mids and overall improved driver efficiency makes voice and music much clearer - removing the "mud" from the stock front speaker system. (one day I may tackle the rear speakers, but for now it's too much hassle)MOUNTINGHere's where the "needs documentation" comes in. There is none, not one bit. You get 2 speakers, 2 flush mounting rings (as shown together in the picture), 2 surface mounting rings, 2 copper brackets, 2 high pass filters, 2 double sided sticky pads (which appear to be for sticking the HP filters to something for mounting), 4 speed nut clips, and 4 screws.There is NO indication of how it all goes together however. I was mounting these to the factory speakers, so I removed the original driver and bored a 1-3/4" hole through the factory plate - screwed the flush mount rings to the plate using their screws - and then reinstalled the plates in the car, sticking the filter to the rear of the speaker using their sticky pads. How you would "surface mount" them I have no idea.An exploded view of the different mountings at the very least SHOULD be enclosed with them.If what I did sounds like something you would do, then have at them, they are great for the price. However, if the idea of "rolling your own" mounting is at all off-putting - move on to a less "economy" brand.
Date published: 2011-06-06
Rated 3 out of 5 by from Installed in my S-15 Sonoma, good enough.I measured these on and off-axis, flush and surface mounted. Surface mounted they have a huge spike in the 5-10K region. Flush mounted they have a suck-out just below 5K. Distortion rises pretty dramatically under 5K, but the included crossover (while extremely cheap and uber-low quality) addresses the distortion pretty well. Measurements found on this thread:http://techtalk.parts-express.com/showthread.php?p =1678402#post1678402I don't think you could design a better crossover for them, at least WRT component value but you could sub out a cheap mylar cap and 20awg coil from Erse audio, but then the price of the set would triple :)
Date published: 2013-02-06
Rated 4 out of 5 by from Value is an understatementPros:VALUE! These tweeters can certainly hold their own against much more expensive solutions in terms of audio quality. These make a great addition to an aging factory sound system without tweeters. Hands down the best upgrade dollar for dollar one can do.Cons:Very flimsy and all around cheap mounting hardware without instructions. If I was a true audiophile and spent hours each day in my car, I d probably look elsewhere. Also, the green Pyle Plus on the flush mounting hardware. WTH? I hit mine with 0000 steel wool and black plastic spray paint before installing them. Also, I used some adhesive (silicone caulk) on the inside of the door to hold everything in place. Like I said, the mounting hardware is CHEAP.Thoughts:I ditched the included crossover, which appeared to be a 12db @ 5000 Hz high pass filter. This was only because I was looking for a low cost solution (and I had some spare 470 uH inductors from work) and I wanted to make a true crossover network for my factory paper cone full ranges, and 470 uH inductors put the crossover frequency at 1350Hz 1st order butterworth. This is too low, but it still works. I used some cheap 30 uF caps for the high pass section, and for funsies threw in a 470 uF cap for a bass blocker on the woofer. 3000-5000Hz would be a much better crossover frequency, but I feel that a true crossover at 1350 Hz sounds better than running these in parallel with the 6.5 paper cone. The final result were crisp, clear highs, and tight bass and mid response. Not bad for a factory speaker and an uber cheap tweeter. I ll let someone else pay $300 for a component set at best buy that sounds the same. LOL.
Date published: 2013-02-07
Rated 4 out of 5 by from If you didnt knowThe best way to get clear and lasting output with tweeters is to use a filter at least 100w with .55 to 1.0uf and a non-inductive resistor. That adds a least two months to your tweeters if you running an amp over 600watts.
Date published: 2013-09-24
Rated 2 out of 5 by from suxit blew within 20 minutes of hooking up to my alpine head unit, I wired everything correct..been doing this for 17 years.
Date published: 2014-03-13

Product Q&A

Get your questions answered from other customers
who own this product or have experience with it.
If your question requires design or troubleshooting information,
please email tech@parts-expresss.com  for a prompt reply.
Pyle PLST6 1/2" Neodymium Tweeter Pair

Mounting Depth?

What is the mounting depth required for flush mounting these tweeters? I want to install them in a 2008 Corolla, but the spot where the tweeters mount on the stock speakers has about .75'' behind the panel.
Asked by: Charles
1.5 inch
Answered by: Booth man
Date published: 2012-09-27

Customer Projects

Customer projects that include: Pyle PLST6 1/2" Neodymium Tweeter Pair

If you built a project using this product, post it in the Parts Express Project Gallery.

Customer Discussions


If you would like to start a discussion about this product, post a thread in the TechTalk Customer Forum.

Recently Viewed Products

Get Deals
emailed to you every week.

Be the first to hear about new and exciting products,special pricing and incredible deals!

See This Week's "GET DEALS" Email
Parts Express
725 Pleasant Valley Dr.Springboro,OH45066USA
800-338-0531

© 1996-2014 Parts Express, All Rights Reserved

Host-Name:ZNODE1