Presensitized PC Board 4" x 6" Single Sided

These highly accurate, pre-coated positive acting printed circuit boards are constructed of 1/16" glass epoxy with 1 oz. (.0014") of copper per side.
In Stock
Your Price
$9.17
Buy 10+$8.39
Part # 055-106
Share:

Product Details

Presensitized PC Board 4" x 6" Single Sided
These highly accurate, pre-coated positive acting printed circuit boards are constructed of 1/16" glass epoxy with 1 oz. (.0014") of copper per side. Simply attach your positive artwork, expose to a U/V light source (including sun lamps, the sun, special U/V light sources or even normal fluorescent lighting bulbs) and then develop. Develop with developer concentrate, part #340-144. The FR-4 material has a dielectric constant 3.6 at 1MHz.


Presensitized PC Board 4" x 6" Single Sided
  • BrandParts Express
  • Part Number055-106
  • UPC038975140469
  • Product CategoryPC Boards, Etching & Standoffs
  • Unit of MeasureEA
  • Product Rating
    (9 Reviews)
  • Weight0.14 lbs.
  • California Prop 65

    Warning: California residents only. Please note per Proposition 65 that this product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

View similar products to the Presensitized PC Board 4" x 6" Single Sided
in the PC Boards, Etching & Standoffs product category.

Reviews

Presensitized PC Board 4" x 6" Single Sided
Presensitized PC Board 4" x 6" Single Sided is rated 4.4444 out of 5 by 9.
Rated 5 out of 5 by from So easy to useI bought 2 of the 4x6 boards. I like the fact that you print the circuit to a transparency exactly as you need it . I used a laser jet printer and 3M 3300 transparency film , and adobe illustrator to do the art work . With this combination , I was able to produce excellent /clean traces down to a 1/64th of an inch . ( I have done this a time or two --- 1/32 is a sure thing always). The instructions say you do not need an exposure box. While this may be true and work , I used a box with backlight bulbs . You have to use a piece of glass to keep the transparency flat against the circuit board. For faster developing .... Use heated water with the developer. I soaked a bottle of ferric chloride in hot water to heat it up as well --- works much faster. DO wear safety equipment - the developer and FC will burn your eyes .......Now , back to the drawing board to make more stuff.
Date published: 2012-03-03
Rated 5 out of 5 by from Developer is available at this storePart # 340-144.I've never made a pcb board before in my life. The entire process, (exposing, developing, etching, tinning) took less than 2 hours on my first try. Better yet, the results look amazing, everything worked perfectly!
Date published: 2010-03-05
Rated 5 out of 5 by from Great Product!Worked great! Presensitized PCBs from Parts-Express is the way to go!
Date published: 2010-02-01
Rated 5 out of 5 by from Hard to mess upThese are the easiest to use. Make up circuits using Eagle Cad, or whatever. Get some 3M CG3300 transparencies. An alright laser printer, like a brother HL-5240(what I use). Print circuits to transparencies, lie over exposed presensitized boards, expose under a fluorescent light. I use a Lithuania FM54 BL CH, one of those two circular florescent jobs. Expose 7 to 8 minutes, in the very middle and 6 to 8 inches from light. Mix your developer, be sure and heat everything up in the nuker to around 125F to 140F, including etchant when ready. Drop board in developer, cold rinse, drop in etchant. Works for me everytime.
Date published: 2010-01-13
Rated 5 out of 5 by from Works Perfectly. You need to follow directions!!!!After you expose the Pre-sensitised board to the artwork for 15-20 minutes depending on your light source. These boards are very forgiving!You need to remove them from the light and place them in a pan of Developer which is not available from this store! POSITIVE DEVELOPER!! Mixing the developer with very hot tap water will yield your results in about 25 seconds!End of story now go and etch them with Ferric Chloride available at RAT SHACK.Not that hard folks!
Date published: 2009-12-12
Rated 5 out of 5 by from Experimentation Needed, Great Results PossibleI print my PCB art on Grafix Computer-Printable Transparent Plastic Sheets (non-adhesive). Stack two prints carefully for maximum density. You can easily feel the rough surface of the sheet to print on.I expose Parts Express Datak 4X6 boards 15 min. on a fluorescent light box with 20 watt bulb, centering board over bulb. This is my personal setting. You just have to try some small boards until you get your personal settings.Mix 1/2 bottle of Datak developer in Pyrex cup with 1/2 cup water and heat in the microwave for one minute. Again, this works for me personally; you'll probably have to tweak it.Development goes fast. Have cold water running, and pull and rinse the board to stop it as soon as large areas start clearing. Make several immersions.Etching solution (ferric chloride) is widely available on the Internet. Etch with agitation in a shallow plastic container and with the board facing down. Periodically rinse board to clear partially etched copper. Etchant is very messy.
Date published: 2009-02-17
  • 2015-08-29T09:05CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.6
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_9
  • loc_en_US, sid_055-106, PRD, sort_mostRecent
  • clientName_PartsExpressInternational

Product Q&A

Get your questions answered from other customers
who own this product or have experience with it.
If your question requires design or troubleshooting information,
please email tech@parts-expresss.com  for a prompt reply.
Presensitized PC Board 4" x 6" Single Sided

Recently Viewed Products

Get Deals
emailed to you every week.

Be the first to hear about new and exciting products,special pricing and incredible deals!

See This Week's "GET DEALS" Email
Parts Express
725 Pleasant Valley Dr.Springboro,OH 45066USA
800-338-0531

© 1986-2015 Parts Express, All Rights Reserved

Host-Name:ZNODE1
Live Chat Software