L-Pad Faceplate For "High"

L-Pad Faceplate For "High"

Overview
Recessed "L" pad housing for flush mounting "L" pads in custom speaker cabinets. Knob included. 2-5/8" x 2-5/8" x 1". For use with any standard 3/8" shaft diameter L-pad.
Part # 
260-268
Weight: 0.066 lbs.  
IN STOCK
Order Soon - Only 3 Left In StockMore Due In May 30, 2014
Your Price
$2.48
Buy 10-up$2.35
Part # 260-268
Qty:  EA
Available Payment Methods

Product Details

L-Pad Faceplate For "High"
Recessed "L" pad housing for flush mounting "L" pads in custom speaker cabinets. Knob included. 2-5/8" x 2-5/8" x 1". For use with any standard 3/8" shaft diameter L-pad.


L-Pad Faceplate For "High"
  • BrandParts Express
  • Part Number260-268
  • UPC844632017131
  • Product CategorySpeaker L-pads
  • Unit of MeasureEA
  • Product Rating
    (4 Reviews)
  • Weight0.066 lbs.
  • California Prop 65

    Warning: California residents only. Please note per Proposition 65 that this product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Similar Products

View similar products to the L-Pad Faceplate For "High"
in the Speaker L-pads product category.

Reviews

L-Pad Faceplate For "High"
L-Pad Faceplate For "High" is rated 4.5 out of 5 by 4.
Rated 5 out of 5 by from You also need these tools to install them...I use a lot of these and I like them, but here's the info that is missing from the Specifications section: To mount these flat or completely flush and keep from bending or breaking the mounting tabs you will need to mount these in a 2-5/16" hole. This is an odd size for a hole saw, so you won't likely find at the corner hardware store, but you can get them from your favorite on-line industrial supply. You can get by with the much more common 2-1/4" size, but you will need to slightly chamfer the edges of the hole. They also require #6 flathead mounting screws, which are not included.
Date published: 2013-12-20
Rated 4 out of 5 by from refurbish partsI am helping an audiophile customer refurbish some 1986 custom built JBL speakers. the old face plates were worn and broken in the corners. I looked through all of my local electronic boutiques and nothing remotely close. these plates were an EXACT match. thank you again parts express!
Date published: 2013-12-20
Rated 4 out of 5 by from Makes Flush-Mounting Simple!I bought a set of L-pads (260-262) and wanted to flush mount them. This kit did the job nicely and cheaply. Only ultra-minor gripe is the outer mounting tabs are slightly elevated because the mounting plate is beveled. If you tighten the plates down the tabs bend over giving it an odd appearance. I backed off on the screws and it makes them look great. Could have included a set of mounting screws but, I rounded up a set.They worked very nicely.
Date published: 2011-02-17
Rated 5 out of 5 by from Works greatInstalled this plate on cabinet to control L-pad. Looks great installed and fits L-pad shaft like a glove.
Date published: 2011-02-17

Product Q&A

Get your questions answered from other customers
who own this product or have experience with it.
If your question requires design or troubleshooting information,
please email tech@parts-expresss.com  for a prompt reply.
L-Pad Faceplate For "High"

is there a round cut-out to be made for flush mounting this faceplate?

No side view is given
Asked by: DSLV
yes, generally a "hole saw" is used...when you get the part measure it for appropriate hole diameter, making sure there is as much gasket surface as possible while still allowing the part to pass cleanly....then go to your local hardware store, and pick up the appropriately sized hole saw, and arbor, or arbor bit...mark the desired location, pop the hole saw into your hand drill and your ready to go..
Answered by: rulgert
Date published: 2012-03-22

Mounting L-pad in faceplate and enclosure

I see the hole diameter for these faceplates are aprox. 2 5/16" diameter. The 100 W L-pads are aprox. 2 1/2" diameter. Is the cup depth of these faceplates at least 3/4" deep so I do not have interference from the wood enclosures when L-pad is mounted to the faceplate?
Asked by: Chuckwantstoknow
Yes the L-pad is deep enough that the cabinet wall thickness will not interfer with the L-pad body.
Answered by: MattP
Date published: 2013-02-06

Customer Projects

Customer projects that include: L-Pad Faceplate For "High"

If you built a project using this product, post it in the Parts Express Project Gallery.

Customer Discussions


If you would like to start a discussion about this product, post a thread in the TechTalk Customer Forum.

Recently Viewed Products

Parts Express Free Shipping at 98 Dollars

Get Deals
emailed to you every week.

Be the first to hear about new and exciting products,special pricing and incredible deals!

See This Week's "GET DEALS" Email
Parts Express
725 Pleasant Valley Dr.Springboro,OH45066USA
800-338-0531

© 1996-2014 Parts Express, All Rights Reserved

Host-Name:ZNODE1