Get your questions answered from other customers
who own this product or have experience with it.
If your question requires design or troubleshooting information,
please email email@example.com
for a prompt reply.
Heavy Duty Titanium Super Tweeter TW44
hi i have a question, can i use this tweeter with a 15" Peavey Black Widow bass Speaker er
the bass cab that i have this speaker in does not have a a Horn or Tweeter in it, what other parts do i need to buy to install properly in the cab and make it work with the 15" Bass Speaker
you separate mid range horn and tweeter to top off this cab,,,in separate box..
Date published: 2012-04-23
Are these sealed back or not?
If not, does the volume of the sealed back need to be of any certain dimensions?
Yes, this is a sealed tweeter.
Date published: 2012-02-13
I have a pair of Boston Acoustics VR20 towers, can i use this titanium tweeter to replace tweeter on tower?will it sound good?
The Pyramid Heavy Duty Titanium Super Tweeter TW44 is a loud strong upper mid and high frequency tweeter with a crossover point using the supplied capacitor of 2000hz.Your Boston Acoustics VR20 towers (circa 1993 - 1998) are a great 2-way tower speaker designed well before digital sound was the norm. BA traditionally are somewhat mellow speakers. Designed and built in the East coast where architecture is aged wood and lots of upholstered room fixtures, the speakers built in the region are typically more mellow than west coast speakers where the architecture is steel, concrete and modern.The Pyramid Heavy Duty Titanium Super Tweeter TW44is something I would characterise more as a wet coast speaker. Being titanium it has a very strong and flat responce but it is very efficient. When combined with the woofers in your BA towers there is likely to be an imbalance between highs and lows that would require some serious eq to balance out.I am not putting down your BA's, but instead suggesting a conventional tweeter set up rather than a projecting bullet such as Part #: 270-252. This is a reproduction of a phenolic ring tweeter developed by CTS in Kentucky as an OEM for dozens of speaker manufacturers such as Marantz, Acoustic Research (AR), Sony, and many many more.From PE speaker description:This is a drop in replacement for the Marantz Imperial Series cabinet speakers models Marantz Imperial 4 5 6 6G 7 8 and 9 with common part numbers 137-7348N, 137-7350, 137-7816 and 841-1022 and HLM312A. Also used in Radio Shack Nova series cabinets Nova 7b as well as the Altec Lansing Santana 891 speakers, RSL Rogersound Labs, Acoustic Research AR 4x and Rectilinear XI Cabinets from the 70's.I would not be surprised to find it is a direct replacement for your BA Towers. It has a very smooth sound characteristic and should be less harsh and able to be balance with your systems bass - midrange - treble contour controls.Another product available at PE is the Tang Band 25-1742S 1" Fabric Dome. This speaker would be between the titanium tweeter and the phenolic ring tweeter I mentioned above. It would be a strong high end tweeter but is more suited for a 3-way enclosure. Because of the box volume of your towers, you could easily add a mid-range speeker, tweeter and a new crossover and convert them to a great sounding 3-way speaker enclosure. All of the items needed to do this are also available at Parts Express.Good Luck
Date published: 2012-11-30
This tweeter, as a few others I see are rated 4 - 8 ohm. Can you explain
Not that the following stats have much of anything to do with impedance once driven with normal program material, but you can look at other stats such as Revc or DCR to see what value they post. In this particular case, it is 3.5 ohms. Label it as a 4 ohms tweeter if you want and base your crossovers etc on that value.
Date published: 2013-09-25
I was wondering what the cutout diameter of the magnet is.
I front mounted mine over a 3" hole with slots for the two voice coil connectors to pass during mounting.
Date published: 2013-04-11
Can I use these with the crossover in my Cerwin Vega DX-5's?
The crossover in them is set at 5000 hz. Do I have to do any additional work or can I just set them up as is?
These can be wired as-is with that crossover.
Date published: 2013-01-07