Dayton Audio MB75MTM Blank Baffle For 0.75 ft³ MTM Cabinet

Dayton Audio MB75MTM Blank Baffle For 0.75 cu. ft. MTM Cabinet

Brand:| Model: MB75MTM
Overview
Replacement blank baffle for Dayton Audio 0.75 ft³ MTM rectangular and curved-sided speaker cabinets. Sold individually.
Part # 
302-749
Weight: 3.8 lbs.  
IN STOCK
List Price$31.33
You Save24%
Your Price
$23.56
Part # 302-749
Qty:  EA
Available Payment Methods

Product Details

Dayton Audio MB75MTM Blank Baffle For 0.75 cu. ft. MTM Cabinet

Replacement blank baffle for Dayton Audio 0.75 ft³ MTM rectangular and curved-sided speaker cabinets. Sold individually.



Dayton Audio MB75MTM Blank Baffle For 0.75 cu. ft. MTM Cabinet
  • BrandDayton Audio
  • ModelMB75MTM
  • Part Number302-749
  • UPC844632059544
  • Product CategoryReplacement Speaker Baffles
  • Unit of MeasureEA
  • Product Rating
    (4 Reviews)
  • Weight3.8 lbs.
  • California Prop 65

    Warning: California residents only. Please note per Proposition 65 that this product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Similar Products

View similar products to the Dayton Audio MB75MTM Blank Baffle For 0.75 cu. ft. MTM Cabinet
in the Replacement Speaker Baffles product category.

Reviews

Dayton Audio MB75MTM Blank Baffle For 0.75 cu. ft. MTM Cabinet
Dayton Audio MB75MTM Blank Baffle For 0.75 cu. ft. MTM Cabinet is rated 4.5 out of 5 by 4.
Rated 5 out of 5 by from BREX~Nice Innovation For Speaker BuildingOrdered a 2nd set for another project and they fit perfectly, screw holes and all! The finish was nice and they were well packaged! Wrapped in foam and placed in a cardboard container, they were well protected.A great way to have another set of speakers without building another set of cabinets...
Date published: 2012-11-06
Rated 5 out of 5 by from Not a Baffling BaffleI had to replace the original baffle of the PE/Dayton curved-sided cabinets that I bought because I made a mistake in cutting the original baffles. This is a great idea to have these baffle replacements. Concerning the cabinet itself, they are well made and very stylish. Any wife will fall in love with them. I am not a trained audio engineer, but I suspect the curved-side of the cabinet may be an audio plus. I used a considerable amount of stuffing in my MTM array and they sound stunning!
Date published: 2010-03-08
Rated 4 out of 5 by from Parts Express listenedWhat impressed me most about Parts Express and the replacement baffles is that PE responded to a request for addition packaging.I had read about someone having problems with insufficient packaging for a similar baffle so I added a comment requesting that the baffle be packaged with sufficient packaging. I noticed on the packing note that the request had made its way all the way to the shipping department and was held awaiting special packaging. Well done PE.The best way to route the drive unit holes is to put Contact brand shelf liner or similar on the baffle before marking and routing, if possible use a new router bit and start with a light 1st cut just deep enough to make it through the layer of paint. My 1st attempt I used masking tape, this lifts up and gets stuck to the router base and makes it very hard to get an accurate cut.
Date published: 2009-02-17
Rated 4 out of 5 by from A1FINE PRODUCT
Date published: 2008-11-24

Product Q&A

Get your questions answered from other customers
who own this product or have experience with it.
If your question requires design or troubleshooting information,
please email tech@parts-expresss.com  for a prompt reply.
Dayton Audio MB75MTM Blank Baffle For 0.75 cu. ft. MTM Cabinet

What is the difference between the 302-745 and the 302-749

They both claim to be "Blank Baffle For 0.75 ft³ MTM Cabinet"
Asked by: buyer
The 302-745 is for our older 0.75ft³ MTM cabinets, where the 302-749 is for our current cabinets. The older cabinets had a slightly different bolt pattern to the baffle, and the mounting bolts are inset to accommodate a ball-and-socket grill mount. The newer cabinets use a magnetic grill which attaches to the mounting bolts, so those bolts will be flush to the face of the cabinet, rather than countersunk.
Answered by: RussR
Date published: 2013-02-28

Customer Projects

Customer projects that include: Dayton Audio MB75MTM Blank Baffle For 0.75 cu. ft. MTM Cabinet

If you built a project using this product, post it in the Parts Express Project Gallery.

Customer Discussions


If you would like to start a discussion about this product, post a thread in the TechTalk Customer Forum.
Get Deals
emailed to you every week.

Be the first to hear about new and exciting products,special pricing and incredible deals!

See This Week's "GET DEALS" Email
Parts Express
725 Pleasant Valley Dr.Springboro,OH45066USA
800-338-0531

© 1996-2014 Parts Express, All Rights Reserved

Host-Name:ZNODE1