Cigarette Lighter Plug with LED

Cigarette Lighter Plug with LED

Overview
Perfect for replacing old worn-out plugs. An LED illuminates upon inserting the plug into an active 12 volt socket. Includes 5A AGC type fuse.
Part # 
265-562
Weight: 0.05 lbs.  
IN STOCK
List Price$2.99
You Save16%
Your Price
$2.49
Buy 10-99 $2.15
Buy 100-up$1.98
Part # 265-562
Qty:  EA
Available Payment Methods

Product Details

Cigarette Lighter Plug with LED
Perfect for replacing old worn-out plugs. An LED illuminates upon inserting the plug into an active 12 volt socket. Includes 5A AGC type fuse.


Cigarette Lighter Plug with LED
  • BrandParts Express
  • Part Number265-562
  • UPC844632015991
  • Product CategoryCigarette Lighter Plugs & Sockets
  • Unit of MeasureEA
  • Product Rating
    (10 Reviews)
  • Weight0.05 lbs.
  • California Prop 65

    Warning: California residents only. Please note per Proposition 65 that this product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Similar Products

View similar products to the Cigarette Lighter Plug with LED
in the Cigarette Lighter Plugs & Sockets product category.

Reviews

Cigarette Lighter Plug with LED
Cigarette Lighter Plug with LED is rated 4.7 out of 5 by 10.
Rated 5 out of 5 by from Cigarette Lighter Plug with LEDThis plug looks great as a replacement. When attached correctly looks nealy factory. Excellent product i used the plugs to replace the ones on my dash lights after they were damaged in a accident.
Date published: 2013-08-22
Rated 5 out of 5 by from Just what I neededI purchased this product to replace my old cig lighter plug which cracked. I am very pleased with this new cig plug. It is better than the original. It was easy to solder and works fine. I used it on my auto air compressor and it is just what I needed.
Date published: 2012-10-05
Rated 5 out of 5 by from I am VERY empressedI am currently manufacturing out of my work shop. For my first production run, I purchased a hundred of the Cigarette Lighter Plugs with LED for my Patent Pending submersible LED fishing light. It requires 20 feet of lead wire with Lighter Plugs attached at one end.For the sake of time management and efficiency, I completely disassembled (very easy) every one and separated each part into separate trays. I recognized the LED Lighter Plug was consistent, uniform in design, and all the parts are interchangeable. This eliminated my concern for reassembling as a mix and match (very easy).FOR THOSE WHO MANUFACTURE.With my hands free lighted 30x magnify glass, portable filtration unit (evacuates solder fumes) variable temperature soldering station, Solder 60/40 Tin/Lead, I went to work.First, I tinned ( 490 degrees) ALL of the Led Lighter Plugs.Second, set the soldering iron at 600 degrees. As I tinned each lead wire, I then place (first) the positive lead wire on the Led Plug Lighter contact (The "top" terminal which is connected to the resistor, the small tan colored part with stripes).Place the tip of the solder iron over the lead wire to heat and fuse the lead wire and Led Plug Lighter contact together,(same temperature 600 degrees). I solder all of the Led Lighter Plugs before the next step.Third, reassemble all the Led Lighter Plugs. That It!PSThere was NOT ONE defective Led Lighter Plug.
Date published: 2012-08-02
Rated 4 out of 5 by from Fixed my DC compressorBought this to replace the plug on a "trunk" Air Compressor...EZ to install...the compressor's working once again.
Date published: 2010-12-03
Rated 4 out of 5 by from Worked greatThe thermal plastic body handles the heat of the soldering iron connections just fine.
Date published: 2009-08-27
Rated 4 out of 5 by from Be careful when you solderThe only downside to this item is that the + contact uses a plastic locating pin which could be damaged by heat when soldeing the leads in place. Just make sure you have a good iron and dont spend to much time getting the joint up to temp.
Date published: 2008-08-20

Product Q&A

Get your questions answered from other customers
who own this product or have experience with it.
If your question requires design or troubleshooting information,
please email tech@parts-expresss.com  for a prompt reply.
Cigarette Lighter Plug with LED

How do you attatch - & + wires in the plug?

Both - & + contacts in the plug are wired together.
Asked by: gpfsr
Please refer to the photo I've attached below. The terminals are not wired together, they should most definitely be de-coupled, although it may not be obvious at first glance. The "top" terminal which is connected to the resistor (the small tan colored part with stripes) is your positive terminal. The "lower" terminal which is connected directly to the LED is the negative. The circuit with the resistor and the LED is there to activate the LED indicator when current is applied to the device. When power is disengaged, the LED will not light.
Answered by: RussR
Date published: 2013-12-10

Customer Projects

Customer projects that include: Cigarette Lighter Plug with LED

If you built a project using this product, post it in the Parts Express Project Gallery.

Customer Discussions


If you would like to start a discussion about this product, post a thread in the TechTalk Customer Forum.

Recently Viewed Products

Get Deals
emailed to you every week.

Be the first to hear about new and exciting products,special pricing and incredible deals!

See This Week's "GET DEALS" Email
Parts Express
725 Pleasant Valley Dr.Springboro,OH45066USA
800-338-0531

© 1996-2014 Parts Express, All Rights Reserved

Host-Name:ZNODE1