500K Audio Taper Potentiometer with Switch 1/4" Shaft

500K Audio Taper Potentiometer with Switch 1/4" Shaft

Overview
Audio taper 1/4 watt monaural potentiometer with M8 x 6.5 mm L bushing. Built-in switch turns power source on and off with volume control.
Part # 
023-600
Weight: 0.038 lbs.  
IN STOCK
List Price$3.49
You Save38%
Your Price
$2.15
Buy 10-up$2.04
Part # 023-600
Qty:  EA
Available Payment Methods

Product Details

500K Audio Taper Potentiometer with Switch 1/4" Shaft
Audio taper 1/4 watt monaural potentiometer with M8 x 6.5 mm L bushing. Built-in switch turns power source on and off with volume control.


Product Specifications
  • Electrical CharacteristicsLogarithmic / Audio Taper
  • Value500K Ohm
500K Audio Taper Potentiometer with Switch 1/4" Shaft
  • BrandParts Express
  • Part Number023-600
  • UPC844632079801
  • Product CategoryPotentiometers
  • Unit of MeasureEA
  • Product Rating
    (7 Reviews)
  • Weight0.038 lbs.
  • California Prop 65

    Warning: California residents only. Please note per Proposition 65 that this product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Similar Products

View similar products to the 500K Audio Taper Potentiometer with Switch 1/4" Shaft
in the Potentiometers product category.

Reviews

500K Audio Taper Potentiometer with Switch 1/4" Shaft
500K Audio Taper Potentiometer with Switch 1/4" Shaft is rated 4.4286 out of 5 by 7.
Rated 3 out of 5 by from Odd PotThis is a good but odd pot. It has a US standard 1/4" (6.35mm) diameter shaft but a Japan standard 8mm (.314") diameter bushing. That makes it hard to retrofit into a chassis that a 3/8 (.375)" bushing pot came out of. PE should restock its pots with all US standard parts. Yes, Alpha does supply them.
Date published: 2013-11-10
Rated 5 out of 5 by from best purchasewas a good product at a very good price was impressed as parts are getting very hard to get these days 73 john
Date published: 2013-10-20
Rated 5 out of 5 by from Works as advertised.Volume control works just as expected. I was hoping to find the volume control without the off/on switch attached but there was plenty of room in the old radio to have the additional length. This worked just fine. Glad to have a source of this type component around.
Date published: 2013-02-15
Rated 5 out of 5 by from Potentiometer with SW works like it should!Other poteniometers that I have purchased was a waste of money as the variable tap is not zero when first turned on thus volume is loud at the min rotation. I restore older radios and this pot works correctly!
Date published: 2012-11-29
Rated 5 out of 5 by from Great Relacement for Vintage RadiosThis control works as expected... the volume goes to zero when turned all the way down and the operation feels smooth. The size is a bit smaller than the old controls I replace making the retro-fit easy, and if shaft coupling or modification is necessary the 1/4" aluminum shaft is easy to work modify. This is my favorite control, hands down!
Date published: 2012-11-16
Rated 3 out of 5 by from Not suitable for RCA Vintage Radio ChassisElectrically, the product works fine. However it's physical size has been whittled down making it too small as a replacement for the typical RCA 2X, 9X, 8X, 56X, 66X vintage radio chassis. Take careful measurements as these radios require a 1.5 inch shaft length for proper knob interface. This product has a shaft length of just 1.25. Also, the threaded mounting area has been reduced to a diameter of about 9/64 while the original RCA pot has a threaded area of 3/8. Therefore, this item is too small for the chassis hole. There is a very thin flat washer supplied you can bend with your fingers however no lock washer is supplied. The hex nut has been reduced from 1/2" OD to 7/16". In summary, just about every aspect of this unit has been reduced in size. Even the solder lugs and insulator are thinner.
Date published: 2012-05-27

Product Q&A

Get your questions answered from other customers
who own this product or have experience with it.
If your question requires design or troubleshooting information,
please email tech@parts-expresss.com  for a prompt reply.
500K Audio Taper Potentiometer with Switch 1/4" Shaft

Could you tell me how long is the shaft?

Asked by: Ralph928
The shaft length is 1-5/16".
Answered by: MattP
Date published: 2014-03-27

What is the shaft length?

Asked by: cwdocbekker
The shaft itself is approximately 1-5/16" in length.
Answered by: RussR
Date published: 2012-06-01

Customer Projects

Customer projects that include: 500K Audio Taper Potentiometer with Switch 1/4" Shaft

If you built a project using this product, post it in the Parts Express Project Gallery.

Customer Discussions


If you would like to start a discussion about this product, post a thread in the TechTalk Customer Forum.
Get Deals
emailed to you every week.

Be the first to hear about new and exciting products,special pricing and incredible deals!

See This Week's "GET DEALS" Email
Parts Express
725 Pleasant Valley Dr.Springboro,OH45066USA
800-338-0531

© 1996-2014 Parts Express, All Rights Reserved

Host-Name:ZNODE1
Live Chat Software