110 Ohm 1W Flameproof Resistor 10 Pcs.

110 Ohm 1W Flameproof Resistor 10 Pcs.

Overview
These metal oxide power resistors feature an excellent flame retardant coating and stable performance in diverse environments. Each resistor is 1 watt with a 5% tolerance. Package of 10 pieces.
Part # 
003-110
Weight: 0.0013 lbs.  
IN STOCK
Your Price
$0.85
Buy 10-up$0.79
Part # 003-110
Qty:  PK
Available Payment Methods

Product Details

110 Ohm 1W Flameproof Resistor 10 Pcs.
These metal oxide power resistors feature an excellent flame retardant coating and stable performance in diverse environments. Each resistor is 1 watt with a 5% tolerance. Package of 10 pieces.


Product Specifications
  • Resistance110 ohms
  • CompositionMetal Oxide Film
  • Power Rating1 Watt
  • Tolerance5%
110 Ohm 1W Flameproof Resistor 10 Pcs.
  • BrandParts Express
  • Part Number003-110
  • UPC844632029899
  • Product CategoryMetal Oxide Resistors
  • Unit of MeasurePK
  • Weight0.0013 lbs.
  • California Prop 65

    Warning: California residents only. Please note per Proposition 65 that this product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Similar Products

View similar products to the 110 Ohm 1W Flameproof Resistor 10 Pcs.
in the Metal Oxide Resistors product category.

Reviews

110 Ohm 1W Flameproof Resistor 10 Pcs.

Product Q&A

Get your questions answered from other customers
who own this product or have experience with it.
If your question requires design or troubleshooting information,
please email tech@parts-expresss.com  for a prompt reply.
110 Ohm 1W Flameproof Resistor 10 Pcs.

Is 1w enough?

I want to build a top box with 4, 4 ohm super tweeters. Wired in 2 parallel sets of 2 in series, for a total of 4 ohm. I also want to add a HP filter set to somewhere between 10 and 15kHz. Should I put a filter over each driver? Or just on the input? And with up to 600w available for input into the box (rated at 1k) wouldn't 1w be too little disipation, even granted that the vast majority of the enegy is going to go through the driver(s)? Sorry for duplication, but I have similar concerns with the capacitors. I'v considered wiring the resistors in 2 sets of 2 as well, to split the current, but wouldn't that mess with the function of the filter??
Asked by: QSCConfused
The filter circuit it is looking at the total load of 4 ohms, so only one network is needed.The caps. should be rated to 250 volts or more as this increases the power handling.Combineing resitors into a network to handle more power is the way to go,the rest of the circuit see this as 'a' load.You get better heat dissapation then if you only used one high wattage resitor. As far as total power handling , apx. 75% or more of the power is below 600 - 1KHz,at 10KHz. you are looking at 5% or less of the total signal.I would be surpised if you ever put more than 10 watts through these drivers.Your ears are more senstive to highs and the motors for high freqs. are that more efficent.i.e. each octave below this point requires twice the power and excursion to have the same 'apparent' volume.
Answered by: alskagram
Date published: 2012-07-07

Customer Projects

Customer projects that include: 110 Ohm 1W Flameproof Resistor 10 Pcs.

If you built a project using this product, post it in the Parts Express Project Gallery.

Customer Discussions


If you would like to start a discussion about this product, post a thread in the TechTalk Customer Forum.

Recently Viewed Products

Get Deals
emailed to you every week.

Be the first to hear about new and exciting products,special pricing and incredible deals!

See This Week's "GET DEALS" Email
Parts Express
725 Pleasant Valley Dr.Springboro,OH45066USA
800-338-0531

© 1996-2014 Parts Express, All Rights Reserved

Host-Name:ZNODE1
Live Chat Software